Paint over Rust with Underbody Gloss Black Paint, Gallon, TRC-15, RUST-BITE

Description

This sale is for one gallon of Paint over Rust with Underbody Gloss Black Paint, TRC-15, RUST-BITE
TRC-15 Gloss Black
• Home • Auto Restoration • Industrial • Fleet •
Marine •
TECHNICAL DATA
SUGGESTED USES:
Heavy equipment, trucks, snow plows, mower decks,
tractors and other
farm machinery, oil field equipment, boat trailers,
buses, military vehicles,
dumpsters, roll offs, fork lifts, propane tanks,
truck bodies, storage tanks,
structural steel, pipes, iron works, gates, fence
posts, chain link, steel truck
rims, metal roofs, sheds, and concrete floors.
DESCRIPTION:
Rust-Bite is a high solids, VOC compliant, single
component rust preventive
and underbody coating specifically formulated to
permanently stop
corrosion without the use of primers or topcoats.
Rust-Bite protects many
surfaces from water, chemicals, salt, and other
corrosive contaminants. Rust-
Bite stops rust when applied to rust that is
prepared by using a wire brush or
hand scraper to remove all loose rust or scale. For
optimum adhesion
sandblast with medium grit. Rust-Bite will dry to a
flexible rock hard, nonporous
finish that will not crack, chip, flake or peel.
Rust-Bite cures by
reacting with atmospheric moisture and its cured
film resembles that of a
powder coating or a baked-on finish with the use of
no hardeners or heat.
Rust-Bite seals and protects many surfaces from
road salt, gasoline, diesel
fuel, oils, battery acids, hydraulic fluids,
solvents, chemicals, or corrosives.
Rust-Bite can be top coated with any industrial or
automotive finish.
PREPARATION
Remove all dirt, grease or oils, clean surfaces
using a Wax & Grease
Remover or equivalent. For heavy build-up scrape or
wire brush excess
material prior to degreasing. Allow surfaces to dry
thoroughly. NOTE: Do
not apply Rust-Bite if atmospheric temperature is
below 50°F.
RUSTED SURFACES:
Remove loose rust and scale using a stiff wire
brush, by grinding, or hand
tool cleaning. Remove all loose, peeling or
bubbling paint. NOTE: Rust-Bite
works best when applied directly over rust. NOTE:
Do not remove all rust or
apply any type of Rust Converter before applying
Rust-Bite.
BARE, SMOOTH METAL:
Sandblasting is recommended but sanding with 36 to
80 grit sand-paper is
also acceptable. When blasting, provide a medium to
coarse profile for
optimum adhesion. Avoid any media that may leave a
smooth surface.
PAINTED SURFACES:
Previously painted surfaces should be sanded using
a 120 to 180 grit
sandpaper to remove gloss.
MIXING & HANDLING:
Container may be under slight pressure. Stir liquid
gently until uniformly
mixed. Do not shake, shaking will cause Rust-Bite
to build pressure in can.
Never work directly from the Rust-Bite can unless
the entire contents will be
used in a single painting session. Always pour what
will be used into a
separate container.
NOTE: Never pour unused product
back into original
container after use.
NOTE: Before closing Rust-Bite
container apply a sheet
of plastic or food wrap over can, Rust-Bite will
adhere lid to can if plastic is
not applied.
Never allow can to sit opened when not
in use. WEAR
GLOVES DURING USE Skin contact should be avoided.
Do not attempt to
remove dried Chassis Saver from skin with solvent;
soak in warm, soapy
water. Once product has stained skin, only time
will remove it.
APPLICATION & REDUCING:
Apply 2-4 coats allowing 3 to 8 hours between coats
depending on temp
and humidity. Each coat should be dry to touch with
no tackiness before
applying next coat. Rust-Bite is a moisture cure
finish which when applied
too heavy will have a tendency to bubble while
curing. Avoid bubbling by
applying thin coats only. Higher temps and humidity
will shorten drying
time. Low temp and humidity will lengthen dry. Do
not apply Rust-Bite if
temperature is below 50°F. Never use lacquer
thinner as a reducer for Rust-
Bite or to wipe surfaces prior to painting.
BRUSH APPLICATION:
Apply thin, even coats using a nylon brush. For
better flow and leveling, add
up to 10% TRC-01 Reducer.
SPRAY APPLICATION:
Reduce up to 10% using TRC-01 Reducer. Apply
medium-wet coats while
maintaining a gun distance of 12 to 14 inches.
Spray tip size should be: 1.2 to
1.4mm.
NOTE:
For surfaces that will be
exposed to UV (sunlight), wait 24 hours, sand and apply a UV resistant single stage urethane paint.
RECOAT:
For films cured over 24 hours, sand using 400-grit
abrasive to remove
gloss before recoating.
Health and
Safety:
See Safety
Data Sheet and labels for additional safety information and handling
instructions.
* The
contents of this package may have to be blended with other components before
the product can be used. Before opening the packages, be sure you understand
the warning messages on the labels and SDS’s of all components, since
the mixture
will have the hazards of all its parts.
* Improper
handling and use, for example, poor spray technique, inadequate engineering
controls and or lack of Personal Protective Equipment (PPE), may result in
hazardous conditions or injury.
* Follow
spray equipment manufacturer’s instructions to prevent personal injury or fire.
* Provide
adequate ventilation for health and fire hazard control.
* Follow
company, product SDS and respirator manufacturer’s recommendations for
selection and proper use of respiratory protection. Be sure employees are
adequately trained on the safe use of respirators per company and regulatory
requirements.
* Wear
appropriate PPE such as eye and skin protection. In the event of injury, see
first aid procedures on SDS.
* Always
observe all applicable precautions and follow good safety and hygiene
practices.
* Safety Data
Sheets are available on website.